短型鼓形齒聯軸器可以用短齒型滾刀和插刀加工內外齒在單件、小批量生產時, 湖北多力多傳動軸有限公司也可以采用標準滾刀用左右切入法進行加工亦稱為左右軸向竄刀法。短型鼓形齒聯軸器先將滾刀徑向切入到齒輪規定的齒全深, 然后根據實測齒厚余量, 使滾刀分別作等量的左右切向切入進給。在一般齒輪制造廠可以采用, 但操作麻煩，效率低，且易造成齒形誤差, 影響齒形精度。

鼓形齒聯軸器的齒頂高系數，徑向間隙系數，全齒高模數，內外齒分度圓弧齒厚大致相等。鼓形齒聯軸器的主要優點是內外齒加工工藝性較好, 可用標準齒輪滾刀和插齒刀進行加工。但是這種鼓形齒聯軸器的外齒齒根抗彎強度比內齒套的齒形要低， 因此,外齒往往先于內齒磨損而折斷，從而使聯軸器失效。為提高外齒抗彎強度，聯軸器承載能力和壽命的關鍵所在。

為提高鼓形齒聯軸器的外齒強度常采用的方法是減薄內齒齒厚而增加外齒齒厚, 使內外齒的抗彎強度接近一致, 另一種方法是采用短齒型內外齒, 降低外齒齒高,以提高外齒的抗彎強度。短型鼓形齒聯軸器具有較好的加工工藝性, 但承載能力和壽命不能滿足客戶的需求。短型鼓形齒聯軸器具有承載能力高、使用壽命長、加工工藝性好、生產等優點，一般聯軸器的內齒加工方法—竄牙切向切入法進行加工。為了內外齒在運轉時具有好的穩定性， 大多以外齒齒頂圓和內齒齒根圓為定心基準。

一般內齒齒根圓精度為，內齒一般加工方法是采用標準齒高的普通插齒刀，用徑向切入法切至全齒深，并根圓公差要求。齒厚仍大于尺寸要求，需進一步插切，但根圓尺寸已到，所以只能采用竄動工件齒牙的切向切入法。即工件在擂刀不轉動的情況下, 相對多轉的角度，然后繼續插削，直至齒厚達到圖紙要求。特殊短厚齒型鼓形齒聯軸器的內齒, 也可以采用竄齒切向切入法進行加工。